Shopping Basket
Your Basket is Empty
There was an error with PayPalClick here to try again
CelebrateThank you for your business!You should receive an order confirmation from Paypal shortly.Exit Shopping Basket


Prices include VAT and customs charges in EU.

Free Worldwide shipping on orders over 50 ​euros.



view:  full / summary


Posted by maltatackle on 28 December, 2011 at 15:20

Speed is very important. The higher the gear ratio, the larger the spool, the faster the retrieve. This makes it easier to get gear in and keep a tight line while backing down when fish moves towards you.

Power is the effort taken to wind the handle against the pressure of the line. The higher the gear gear ratio, the harder it is to wind the handle. you will realise the importance of power when you clear rods after a strike, when having to gain line under load and when enjoying an extended battle.

To change speed and power most brands of reels have two speeds like the Omoto GTR and Omoto Poseidon reels. Changing speed or , more precisely, changing gears, does not have anything to do with drag settings. The reel will be in high speed most of the time. Low gear is used when you want to turn a fish by putting maximum pressure on by keeping the rod high and using very slow, short strokes, gaining only a few inches at a time. If a fish is deep and you cannot wind against the stretched line, low speed will enable you to do so. During a long fight, a tired angler can relax by dropping to low gear and winding steadily without necessarily pumping the rod. This gives the angler time to have a rest while keeping pressure on the fish and gaining line. As soon as you can gain line easily on low speed, resume high speed.

Drags, also known as clutches, must be smooth. The preference is for lever drag reels such as Omoto GTR and Omoto Poseidon reels. Lever drags allow you to set a known drag in a known position on their drag lever arc. They often have strike buttons and markings for your preferred settings. This type of drag allows you to fight by increasing or decreasing pressures as fight progresses, while always knowing where your predefined setting is.

To check the drag set your drag to one third the breaking strain of the main line. Get someone to pull the line smoothly. If the tip jerks service the drag. Clean your drags with white spirits and let them dry before reassembling them. Do not over grease the gears, too much grease clogs the gears and may restrict your free spool.

The art of trolling artificial lures.

Posted by maltatackle on 28 December, 2011 at 15:10

Artificial lures are an effective weapon for catching large game fish and the most spectacular of all. In many cases it is the most effective. The best news is that trolling lures is very easy to do. A novice can be very competitive with just a basic knowledge of lure trolling.

When using Iland lures for big fish like Albacore, Dolphinfish, Tuna, Bonito, Spearfish, Swordfish etc, the biggest difference is the speed. In blue water these lures are trolled at effective speeds from a minimum of 6 knots, mostly between 5 to 8 knots and some lures like the Iland Sea Searcher as fast as 16 knots with the accompanying noise, vibration and white water. These components actually combine to attract fish.

Many anglers, because of their previous experience with other forms of trolling, run their lures way back out past the end of the wash, fearing that the boat noise and wash will scare the fish. In this form of fishing this is not the case. The action is concentrated in the area between the transom and the end of the prop wash and turbulence. this is known as the Strike Zone. This area is where you should run your lures. White water is at its deepest at the transom, with the maximum depth at the props. Along the side of the prop wash there are alleys of clearer water with little or no white water turbulence; a nice place to run a lure, as it would be very visible.

In the Strike Zone are the waves following the boat. These are pressure waves kicked up by the boat and vary in size depending on the boat size and hull type. These waves are the most important part of the wash for trolling skirted lures, as they are run and carefully positioned or tuned on the leading face of the pressure wave. Some boats do not have pressure waves, in which case the positioning of lures is less critical.

A lure that is working properly comes to the surface, greps air 'breathing', dives down leaving a long bubble trail, 'smoking' and when it stops smoking, it comes up for another breath. It should not run under the water without a smoke trail for any length of time, if it does; it is called lazy. Also, it should not come out of the water, blowing out when breathing. Smoke trails vary from pencil thin to almost creating their own prop wash. This mainly depends on the shape of the lure head, lure length and trolling speed. How often a lure goes through the working cycle depends on sea conditions, boat speed, lure position, line class and rigging.

Trolling lures only results in catching fish given certain situations. In fact they are the same situations that lead to success in every other form of fishing. Quite simply fishing where the fish are, and even more than that, being where the fish are at the time they are feeding.

Table of the line diameters (in mm) to PE numbers

Posted by maltatackle on 28 December, 2011 at 15:05